t_connect(3)t_connect(3)NAMEt_connect() - establish a connection with another transport user
SYNOPSISDESCRIPTION
This function enables a transport user to request a connection to the
specified destination transport user. This function can only be issued
in the state. fd identifies the local transport endpoint where commu‐
nication will be established. sndcall and rcvcall point to a structure
which contains the following members:
The type structure is defined in the or header file. This structure,
which is used to define buffer parameters, has the following members:
maximum byte length of the data buffer
actual byte length of data written to buffer
points to buffer location
sndcall specifies information needed by the transport provider to
establish a connection. rcvcall specifies information that is associ‐
ated with the newly established connection.
In sndcall, addr specifies the protocol address of the destination
transport user. opt presents any protocol-specific information that
might be needed by the transport provider. udata points to optional
user data that may be passed to the destination transport user during
connection establishment. sequence has no meaning for this function.
On return in rcvcall, addr returns the protocol address associated with
the responding transport endpoint. opt presents any protocol-specific
information associated with the connection. udata points to optional
user data that may be returned by the destination transport user during
connection establishment. sequence has no meaning for this function.
The opt argument permits users to define the options that may be passed
to the transport provider. These options are specific to the underly‐
ing protocols of the transport provider and are described for ISO and
TCP protocols in Appendix A, "ISO Transport Protocol Information," Ap‐
pendix B, "Internet Protocol-specific Information," and Appendix F,
"Headers and Definitions" of the manual. The user may choose not to
negotiate protocol options by setting the len field of opt to zero. In
this case, the provider may use default options.
If the opt argument is used, the sndcall->opt.buf structure must point
to the corresponding options structures. For XTI over the OSI trans‐
port provider, the options buffer should be a struct of type or For
TLI, see the documentation for the transport provider being used. The
maxlen and buf fields of the structure pointed by rcvcall->addr and
rcvcall->opt must be set before the call.
The udata argument enables the caller to pass user data to the destina‐
tion transport user and receive user data from the destination user
during connection establishment. However, the amount of user data must
not exceed the limits supported by the transport provider as returned
in the connect field of the info argument of or If the len of udata is
zero in sndcall, no data will be sent to the destination transport
user.
On return, the addr, opt, and udata fields of rcvcall will be updated
to reflect values associated with the connection. Thus, the maxlen
field of each argument must be set before issuing this function to
indicate the maximum size of the buffer for each. However, rcvcall may
be a null pointer, in which case no information is given to the user on
return from
By default, executes in synchronous mode and will wait for the destina‐
tion user's response before returning control to the local user. A
successful return (i.e., return value of zero) indicates that the
requested connection has been established. However, if is set (via or
executes in asynchronous mode. In this case, the call will not wait
for the remote user's response, but will return control immediately to
the local user and return −1 with set to [TNODATA] to indicate that the
connection has not yet been established. In this way, the function
simply initiates the connection establishment procedure by sending a
connect request to the destination transport user. The function is
used in conjunction with to determine the status of the requested con‐
nection.
When a synchronous call is interrupted by the arrival of a signal, the
state of the corresponding transport endpoint is allowing a further
call to either or
Valid States
Fork Safety
is not fork-safe.
RETURN VALUE
Upon successful completion, a value of 0 is returned. Otherwise, a
value of −1 is returned and is set to indicate the error.
ERRORS
[TBADF] The specified file descriptor does not refer to a
transport endpoint.
[TOUTSTATE] The function was issued in the wrong sequence.
[TNODATA] was set, so the function successfully initiated the
connection establishment procedure, but did not
wait for a response from the remote user.
[TBADADDR] The specified protocol address was in an incorrect
format or contained illegal information.
[TBADOPT] The specified protocol options were in incorrect
format or contained illegal information.
[TBADDATA] The amount of user data specified was not within
the bounds allowed by the transport provider.
[TACCES] The user does not have permission to use the speci‐
fied address or options.
[TBUFOVFLW] The number of bytes allocated for an incoming argu‐
ment (maxlen) is greater than zero but not suffi‐
cient to store the value of that argument. If exe‐
cuted in synchronous mode, the provider's state, as
seen by the user, changes to and the connect indi‐
cation information to be returned in rcvcall is
discarded.
[TLOOK] An asynchronous event has occurred on this trans‐
port endpoint and requires immediate attention.
[TNOTSUPPORT] This function is not supported by the underlying
transport provider.
[TSYSERR] A system error has occurred during execution of
this function.
[TADDRBUSY] This transport provider does not support multiple
connections with the same local and remote
addresses. This error indicates that a connection
already exists.
[TPROTO] (XTI only) This error indicates that a communica‐
tion problem has been detected between XTI and the
transport provider for which there is no suitable
XTI (
FILES
XTI data structures
TLI data structures
SEE ALSOfcntl(2), t_accept(3), t_alloc(3), t_getinfo(3), t_listen(3),
t_open(3), t_rcvconnect(3), thread_safety(5).
STANDARDS CONFORMANCEt_connect(3)