eri(7D) Devices eri(7D)NAMEeri - eri Fast-Ethernet device driver
SYNOPSIS
/dev/eri
DESCRIPTION
The eri Fast Ethernet driver is a multi-threaded, loadable, clonable,
STREAMS—based hardware driver supporting the connectionless Data Link
Provider Interface dlpi(7P) over an eri Fast-Ethernet controller. Mul‐
tiple eri devices installed within the system are supported by the
driver.
The eri driver provides basic support for the eri hardware and handles
the eri device. Functions include chip initialization, frame transit
and receive, multicast and promiscuous support, and error recovery and
reporting.
The eri device provides 100Base-TX networking interfaces using the SUN
RIO ASIC and an internal transceiver. The RIO ASIC provides the PCI
interface and MAC functions. The physical layer functions are provided
by the internal transceiver which connects to a RJ-45 connector.
The 100Base-TX standard specifies an auto-negotiation protocol to auto‐
matically select the mode and speed of operation. The internal trans‐
ceiver is capable of performing auto-negotiation using the remote-end
of the link (link partner) and receives the capabilities of the remote
end. It selects the highest common denominator mode of operation based
on the priorities. It also supports a forced-mode of operation under
which the driver selects the mode of operation.
APPLICATION PROGRAMMING INTERFACE
The cloning character-special device /dev/eri is used to access all
eri controllers installed within the system.
eri and DLPI
The eri driver is a "style 2" Data Link Service provider. All M_PROTO
and M_PCPROTO type messages are interpreted as DLPI primitives. Valid
DLPI primitives are defined in <sys/dlpi.h>. Refer to dlpi(7P) for more
information.
An explicit DL_ATTACH_REQ message by the user is required to associate
the opened stream with a particular device (ppa). The ppa ID is inter‐
preted as an unsigned integer data type and indicates the corresponding
device instance (unit) number. An error (DL_ERROR_ACK) is returned by
the driver if the ppa field value does not correspond to a valid device
instance number for this system. The device is initialized on first
attach and de-initialized (stopped) at last detach.
The values returned by the driver in the DL_INFO_ACK primitive in
response to the DL_INFO_REQ from the user are as follows:
· The maximum SDU is 1500 (ETHERMTU - defined in <sys/ethernet.h>
).
· The minimum SDU is 0.
· The dlsap address length is 8.
· The MAC type is DL_ETHER.
·
The sap length values is -2, meaning the physical address compo‐
nent is followed immediately by a 2 byte sap component within the
DLSAP address.
· The service mode is DL_CLDLS.
· Optional quality of service (QOS) is not currently supported so
QOS fields are 0.
· The provider style is DL_STYLE.
· The version is DL_VERSION_2.
· The broadcast address value is Ethernet/IEEE broadcast address
(0xFFFFFF).
Once in the DL_ATTACHED state, the user must send a DL_BIND_REQ to as‐
sociate a particular SAP (Service Access Pointer) with the stream. The
eri driver interprets the sap field within the DL_BIND_REQ as an Ether‐
net "type," therefore valid values for the sap field are in the
[0-0xFFFF] range. Only one Ethernet type can be bound to the stream at
any time.
If the user selects a sap with a value of 0, the receiver will be in
IEEE 802.3 mode. All frames received from the media having a Ethernet
type field in the range [0-1500] are assumed to be 802.3 frames and are
routed up all open Streams which are bound to sap value 0. If more than
one Stream is in 802.3 mode, the frame will be duplicated and routed up
multiple Streams as DL_UNITDATA_IND messages.
In transmission, the driver checks the sap field of the DL_BIND_REQ to
determine if the value is 0 or if the Ethernet type field is in the
range [0-1500]. If either is true, the driver computes the length of
the message, not including initial M_PROTO mblk (message block), of all
subsequent DL_UNITDATA_REQ messages, and transmits 802.3 frames that
have this value in the MAC frame header length field.
The eri driver's DLSAP address format consists of the 6 byte physical
(Ethernet) address component followed immediately by the 2 byte sap
(type) component, producing an 8 byte DLSAP address. Applications
should not hardcode to this particular implementation-specific DLSAP
address format but use information returned in the DL_INFO_ACK primi‐
tive to compose and decompose DLSAP addresses. The sap length, full
DLSAP length, and sap/physical ordering are included within the
DL_INFO_ACK. The physical address length can be computed by subtracting
the sap length from the full DLSAP address length or by issuing the
DL_PHYS_ADDR_REQ to obtain the current physical address associated with
the stream.
Once in the DL_BOUND state, the user may transmit frames on the Ether‐
net by sending DL_UNITDATA_REQ messages to the eri driver. The eri
driver will route received Ethernet frames up all open and bound
streams having a sap which matches the Ethernet type as DL_UNITDATA_IND
messages. Received Ethernet frames are duplicated and routed up multi‐
ple open streams if necessary. The DLSAP address contained within the
DL_UNITDATA_REQ and DL_UNITDATA_IND messages consists of both the sap
(type) and physical (Ethernet) components.
eri Primitives
In addition to the mandatory connectionless DLPI message set, the
driver also supports the following primitives:
The DL_ENABMULTI_REQ and DL_DISABMULTI_REQ primitives enable/disable
reception of individual multicast group addresses. A set of multicast
addresses may be iteratively created and modified on a per-stream basis
using these primitives. These primitives are accepted by the driver in
any state following DL_ATTACHED.
The DL_PROMISCON_REQ and DL_PROMISCOFF_REQ primitives with the
DL_PROMISC_PHYS flag set in the dl_level field enables/disables recep‐
tion of all promiscuous mode frames on the media, including frames gen‐
erated by the local host. When used with the DL_PROMISC_SAP flag set,
this enables/disables reception of all sap (Ethernet type) values. When
used with the DL_PROMISC_MULTI flag set, this enables/disables recep‐
tion of all multicast group addresses. The effect of each is always on
a per-stream basis and independent of the other sap and physical level
configurations on this stream or other streams.
The DL_PHYS_ADDR_REQ primitive returns the 6 octet Ethernet address
currently associated (attached) to the stream in the DL_PHYS_ADDR_ACK
primitive. This primitive is valid only in states following a success‐
ful DL_ATTACH_REQ.
The DL_SET_PHYS_ADDR_REQ primitive changes the 6 octet Ethernet address
currently associated (attached) to this stream. The credentials of the
process which originally opened this stream must be superuser, or EPERM
is returned in the DL_ERROR_ACK. This primitive is destructive because
it affects all current and future streams attached to this device. An
M_ERROR is sent up all other streams attached to this device when this
primitive is successful on this stream.
Once changed, all streams subsequently opened and attached to this
device will obtain this new physical address. Once changed, the physi‐
cal address will remain until this primitive is used to change the
physical address again or the system is rebooted, whichever comes
first.
eri DRIVER
By default, the eri driver performs auto-negotiation to select the
mode and speed of the link, which can be in one of the following
modes, as described in the 100Base-TX standard:
· 100 Mbps, full-duplex
· 100 Mbps, half-duplex
· 10 Mbps, full-duplex
· 10 Mbps, half-duplex
The auto-negotiation protocol automatically selects:
· Operation mode (half-duplex or full-duplex)
· Speed (100 Mbps or 10 Mbps)
The auto-negotiation protocol does the following:
· Gets all modes of operation supported by the link partner
· Advertises its capabilities to the Link Partner
· Selects the highest common denominator mode of operation based on
the priorities
The internal transceiver is capable of all of the operating speeds and
modes listed above. By default, auto-negotiation is used to select the
speed and the mode of the link and the common mode of operation with
the link partner.
For users who want to select the speed and mode of the link, the eri
device supports programmable IPG (Inter-Packet Gap) parameters ipg1 and
ipg2. Sometimes, the user may want to alter these values depending on
whether the driver supports 10 Mbps or 100 Mpbs and accordingly, IPG
will be set to 9.6 or 0.96 microseconds.
eri Parameter List
The eri driver provides for setting and getting various parameters for
the eri device. The parameter list includes current transceiver sta‐
tus, current link status, inter-packet gap, local transceiver capabili‐
ties and link partner capabilities.
The local transceiver has two set of capabilities: one set reflects
hardware capabilities, which are read-only (RO) parameters. The second
set reflects the values chosen by the user and is used in speed selec‐
tion and possess read/write (RW) capability. At boot time, these two
sets of capabilities will be the same. Because the current default
value of these parameters can only be read and not modified, the link
partner capabilities are also read only.
FILES
/dev/eri eri special character device.
/kernel/drv/eri.conf System wide default device driver
properties
/kernel/drv/sparcv9/eri 64 bit device driver
SEE ALSOndd(1M), netstat(1M), driver.conf(4), hme(7D), qfe(7D), dlpi(7P)SunOS 5.10 1 Mar 2000 eri(7D)