RSOCKET(7) Librdmacm Programmer's Manual RSOCKET(7)NAMErsocket - RDMA socket API
SYNOPSIS
#include <rdma/rsocket.h>
DESCRIPTION
RDMA socket API and protocol
NOTES
Rsockets is a protocol over RDMA that supports a socket-level API for
applications. Rsocket APIs are intended to match the behavior of cor‐
responding socket calls, except where noted. Rsocket functions match
the name and function signature of socket calls, with the exception
that all function calls are prefixed with an 'r'.
The following functions are defined:
rsocket
rbind, rlisten, raccept, rconnect
rshutdown, rclose
rrecv, rrecvfrom, rrecvmsg, rread, rreadv
rsend, rsendto, rsendmsg, rwrite, rwritev
rpoll, rselect
rgetpeername, rgetsockname
rsetsockopt, rgetsockopt, rfcntl
Functions take the same parameters as that used for sockets. The fol‐
low capabilities and flags are supported at this time:
PF_INET, PF_INET6, SOCK_STREAM, SOCK_DGRAM
SOL_SOCKET - SO_ERROR, SO_KEEPALIVE (flag supported, but ignored),
SO_LINGER, SO_OOBINLINE, SO_RCVBUF, SO_REUSEADDR, SO_SNDBUF
IPPROTO_TCP - TCP_NODELAY, TCP_MAXSEG
IPPROTO_IPV6 - IPV6_V6ONLY
MSG_DONTWAIT, MSG_PEEK, O_NONBLOCK
Rsockets provides extensions beyond normal socket routines that allow
for direct placement of data into an application's buffer. This is
also known as zero-copy support, since data is sent and received
directly, bypassing copies into network controlled buffers. The fol‐
lowing calls and options support direct data placement.
riomap, riounmap, riowrite
off_t riomap(int socket, void *buf, size_t len, int prot, int flags,
off_t offset)
Riomap registers an application buffer with the RDMA hardware
associated with an rsocket. The buffer is registered either for
local only access (PROT_NONE) or for remote write access
(PROT_WRITE). When registered for remote access, the buffer is
mapped to a given offset. The offset is either provided by the
user, or if the user selects -1 for the offset, rsockets selects
one. The remote peer may access an iomapped buffer directly by
specifying the correct offset. The mapping is not guaranteed to
be available until after the remote peer receives a data trans‐
fer initiated after riomap has completed.
riounmap
int riounmap(int socket, void *buf, size_t len)
Riounmap removes the mapping between a buffer and an rsocket.
riowrite
size_t riowrite(int socket, const void *buf, size_t count, off_t off‐
set, int flags)
Riowrite allows an application to transfer data over an rsocket
directly into a remotely iomapped buffer. The remote buffer is
specified through an offset parameter, which corresponds to a
remote iomapped buffer. From the sender's perspective, riowrite
behaves similar to rwrite. From a receiver's view, riowrite
transfers are silently redirected into a pre- determined data
buffer. Data is received automatically, and the receiver is not
informed of the transfer. However, iowrite data is still con‐
sidered part of the data stream, such that iowrite data will be
written before a subsequent transfer is received. A message
sent immediately after initiating an iowrite may be used to
notify the receiver of the iowrite.
In addition to standard socket options, rsockets supports options spe‐
cific to RDMA devices and protocols. These options are accessible
through rsetsockopt using SOL_RDMA option level.
RDMA_SQSIZE - Integer size of the underlying send queue.
RDMA_RQSIZE - Integer size of the underlying receive queue.
RDMA_INLINE - Integer size of inline data.
RDMA_IOMAPSIZE - Integer number of remote IO mappings supported
Note that rsockets fd's cannot be passed into non-rsocket calls. For
applications which must mix rsocket fd's with standard socket fd's or
opened files, rpoll and rselect support polling both rsockets and nor‐
mal fd's.
Existing applications can make use of rsockets through the use of a
preload library. Because rsockets implements an end-to-end protocol,
both sides of a connection must use rsockets. The rdma_cm library pro‐
vides such a preload library, librspreload. To reduce the chance of
the preload library intercepting calls without the user's explicit
knowledge, the librspreload library is installed into %libdir%/rsocket
subdirectory.
The preload library can be used by setting LD_PRELOAD when running.
Note that not all applications will work with rsockets. Support is
limited based on the socket options used by the application. Addition‐
ally, applications which call fork are not supported.
rsockets uses configuration files that give an administrator control
over the default settings used by rsockets. Use files under %syscon‐
fig%/rdma/rsocket as shown:
mem_default - default size of receive buffer(s)
wmem_default - default size of send buffer(s)
sqsize_default - default size of send queue
rqsize_default - default size of receive queue
inline_default - default size of inline data
iomap_size - default size of remote iomapping table
polling_time - default number of microseconds to poll for data before
waiting
All configuration files should contain a single integer value. Values
may be set by issuing a command similar to the following example.
echo 1000000 > /etc/rdma/rsocket/mem_default
If configuration files are not available, rsockets uses internal
defaults. Applications can override default values programmatically
through the rsetsockopt routine.
SEE ALSOrdma_cm(7)librdmacm 2013-01-21 RSOCKET(7)