sg_test_rwbuf man page on Alpinelinux
[printable version]
SG_TEST_RWBUF(8) SG3_UTILS SG_TEST_RWBUF(8)
NAME
sg_test_rwbuf - test a SCSI host adapter by issuing dummy writes and
reads
SYNOPSIS
sg_test_rwbuf [--addrd=AR] [--addwr=AW] [--help] [--quick] --size=SZ
[--times=NUM] [--verbose] [--version] DEVICE
or an older deprecated format sg_test_rwbuf DEVICE SZ [AW] [AR]
DESCRIPTION
sg_test_rwbuf writes and reads back SZ bytes to the internal buffer of
DEVICE (e.g. /dev/sda or /dev/sg0). A pseudo random pattern is written
to the data buffer on the device then read back. If the same pattern is
found 'Success' is reported. If they do not match (checksums unequal)
then this is reported and up to 24 bytes from the first point of mis‐
match are reported; the first line shows what was written and the sec‐
ond line shows what was received. For testing purposes, you can ask it
to write AW or read AR additional bytes.
OPTIONS
Arguments to long options are mandatory for short options as well.
-r, --addrd=AR
Read an additional AR bytes (than indicated by SZ) from the data
buffer. Checksum is performed over the first SZ bytes.
-w, --addwr=AW
Write an additional AW bytes (than indicated by SZ) of zeros
into the data buffer. Checksum is generated over the first SZ
bytes.
-h, --help
Print out a usage message the exit.
-q, --quick
Perform a READ BUFFER descriptor command to find out the avail‐
able data buffer length and offset, print them out then exit
(without testing with write/read sequences).
-s, --size=SZ
where SZ is the size of buffer in bytes to be written then read
and checked. This number needs to be less than or equal to the
size of the device's data buffer which can be seen from the
--quick option. Either this option or the --quick option should
be given.
-t, --times=NUM
where NUM is the number of times to repeat the write/read to
buffer test. Default value is 1 .
-v, --verbose
increase verbosity of output.
-V, --version
print version number (and data of last change) then exit.
NOTES
The microcode in a SCSI device is _not_ modified by doing a WRITE BUF‐
FER command with its mode set to "data" (0x2) as done by this utility.
Therefore this utility is safe in that respect. [Mode values 0x4, 0x5,
0x6 and 0x7 are the dangerous ones :-)]
WARNING: If you access the device at the same time (e.g. because it's a
hard disk with a mounted file system on it) the device's buffer may be
used by the device itself for other data at the same time, and over‐
writing it may or may not cause data corruption! HOWEVER the SPC-3
draft standard does state in its WRITE BUFFER command: "This command
shall not alter any medium of the logical unit when data mode ... is
specified". This implies that it _is_ safe to use this utility with
devices that have mounted file systems on them. Following this theme
further, a disk with active mounted file systems may cause the data
read back to be different (due to caching activity) to what was written
and hence a checksum error.
EXIT STATUS
The exit status of sg_test_rwbuf is 0 when it is successful. Otherwise
see the sg3_utils(8) man page.
AUTHORS
Written by D. Gilbert and K. Garloff
COPYRIGHT
Copyright © 2000-2012 Douglas Gilbert, Kurt Garloff
This software is distributed under the GPL version 2. There is NO war‐
ranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PUR‐
POSE.
sg3_utils-1.35 November 2012 SG_TEST_RWBUF(8)
[top]
List of man pages available for Alpinelinux
Copyright (c) for man pages and the logo by the respective OS vendor.
For those who want to learn more, the polarhome community provides shell access and support.
[legal]
[privacy]
[GNU]
[policy]
[cookies]
[netiquette]
[sponsors]
[FAQ]
Polarhome, production since 1999.
Member of Polarhome portal.
Based on Fawad Halim's script.
....................................................................
|
Vote for polarhome
|