vme_manual_setup(7)vme_manual_setup(7)NAME
vme_manual_setup, sys_attrs_vba_vipvic - Describes how to set up
VIP/VIC-based Alpha VME systems for use on the VMEbus, including how to
modify attributes of the vba_vipvic kernel subsystem
DESCRIPTION
VMEbus setup allows you to run the operating system on the following
VIP/VIC-based AXPvme and Alpha VME systems:
AXPvme single-board computers (SBCs)
Alpha VME 4/224 and 4/228 SBCs
Alpha VME 5/352 and 5/480 SBCs
Alpha VME 2100 system
For information about installing the operating system on the listed
systems, see the Installation Guide.
For information about setting up UNIVERSE II-based Alpha VME systems
for use on the VMEbus, see the sys_attrs_vba_univ(7) reference page.
See System Configuration Supplement: OEM Platforms for detailed infor‐
mation about the use of the VMEbus on the listed systems, including the
following topics: Configuring the vba_vipvic subsystem Configuring VME‐
bus A32 and A24 address spaces Configuring the VMEbus A16 address space
Configuring VMEbus interrupts Using VMEbus hardware byte-swapping modes
Sharing memory between big endian and little endian processors Perform‐
ing VMEbus slave block transfers Performing VMEbus master block trans‐
fers with local DMA Using the realtime interrupt-handling routine
rt_post_callout
The defaults supplied for various VMEbus parameters are listed below.
The default values specified should provide proper VMEbus operation for
most applications. Be careful when modifying these values; not all
adapters support all fields.
Parameter Default Meaning
--------------------------------------------------------------------
VME_Br_Lev 0x03 Bus request level 3 for master cycles
VIC_Arb_Mode 0x00 Arbitration mode is round robin
VME_Fair_Req 0x00 VMEbus fair requester disabled
VIC_Loc_Bus_To 0x05 Local bus timeout period is 256
microseconds
VME_Bus_To 0x06 VMEbus timeout period is 512
microseconds
VIC_Rel_Mode 0 Release mode is release on request
(ROR)
VIC_Syscon 1 System controller VMEbus reset
is enabled
VIC_Wrt_Post 0 Disable VIC master write posting
VIC_DMA_Intrlv 15 DMA interleave gap is 3.75
microseconds (value * 250 nanoseconds)
Lmt_DMA_Rd 0 No DMA read limit
Lmt_DMA_Wrt 0 No DMA write limit
Frce_Hw_DMA 0 Do not force hardware DMA engine fo
SMP system
A32_Base 0x08000000 A32 inbound DMA window base address
A32_Size 0x8000000 A32 window size (128 MB)
A24_Base 0x00C00000 A24 inbound DMA window base address
A24_Size 0x400000 A24 window size (4 MB)
A16_Base 0x00000100 A16 interprocessor communication base
address
A16_Mask 0x00000000 A16 interprocessor communication mask
A24_A32_Ovrlap 1 Inbound A24/A32, if same space, overlap
The following VMEbus interrupt parameters provide initial defaults that
are later overwritten by system priority level (SPL) values supplied by
the platform. See the values listed in System Configuration Supple‐
ment: OEM Platforms, or query the values at run time using the command
sysconfig -q vba_vipvic.
Parameter Default Meaning
--------------------------------------------------------------------
Irq0_SPL 3 VMEbus IRQ level to system SPL map
Irq1_SPL 3 VMEbus IRQ 1 to SPL SPLDEVLOW
Irq2_SPL 3 VMEbus IRQ 2 to SPL SPLDEVLOW
Irq3_SPL 3 VMEbus IRQ 3 to SPL SPLDEVLOW
Irq4_SPL 3 VMEbus IRQ 4 to SPL SPLDEVLOW
Irq5_SPL 3 VMEbus IRQ 5 to SPL SPLDEVLOW
Irq6_SPL 3 VMEbus IRQ 6 to SPL SPLDEVLOW
Irq7_SPL 3 VMEbus IRQ 7 to SPL SPLDEVLOW
Adapt_Blk_SPL 3 Adapter resource blocking SPL
SPLDEVLOW
DMA_Access_Space 0 Adapter MBLT I/O access: sparse
SEE ALSO
Interfaces: sys_attrs_vme_vba(7), sys_attrs_vba_univ(7), syscon‐
figdb(8), sys_attrs(5)
System Configuration Supplement: OEM Platforms, Device Driver Kit man‐
ual Writing VMEbus Device Drivers
vme_manual_setup(7)