USAGE(8)USAGE(8)NAMEusage - installing and using MINIX
DESCRIPTION
This manual page describes the installation and use of MINIX from a
System Administrators point of view. It contains an installation
guide, instructions on how to do the initial configuration and some
other info. Please read this document entirely before attempting to
install MINIX. The installation steps are in the proper order, but not
all the information you may need is presented at the right moment.
Other detailed information that may be useful can be found in boot(8),
hier(7), and in dosminix(8) if you run MINIX under DOS.
1. MINIX UNDER DOS
Installation of MINIX to run under DOS is a nonevent. Chances are, you
are reading this manual page from an already running MINIX system, but
if not then the setup goes like this:
Unpack the DOSMINIX.ZIP file using one of the popular ZIP utilities,
such as PKZIP or WinZIP. Next reboot Windows and hit F8 just when you
see the "Booting Windows" message. From the menu that appears choose
"Command prompt only", or if that doesn't work "Safe mode command
prompt only". Under Windows Me you can use a startup disk to boot the
PC into DOS. Move to the directory containing the MINIX files and
type:
boot minix.mnx
Type '=' and presto, you are running MINIX. Most of the rest of this
manual, which deals mainly with running MINIX in a true hard disk par‐
tition, does not apply to you. Your system is already installed com‐
pletely, with all binaries and sources present, so all the talk about
getting MINIX on your disk can be skimmed over. Pay attention again
when the focus shifts to the configuration of the system. Section 9 is
where this happens first. (The main challange to a DOS installation is
to figure out which parts of the installation manual do not apply.)
2. REQUIREMENTS
The minimum system MINIX can be installed on comfortably is an IBM
PC/AT or PS/2 with a 286 processor, 2 MB memory, a 720 kb diskette
drive, and 35 MB free space on an AT, ESDI, or SCSI hard disk (the lat‐
ter controlled by an Adaptec 1540.) MINIX for the 386 (MINIX-386 for
short) can be installed on a machine with at least a 386sx processor, 3
MB memory and at least 35 MB of disk space.
The minimum system MINIX can be installed on uncomfortably is an IBM
PC/XT with 640 kb memory. MINIX-386 can more or less run in 2 MB mem‐
ory. See sections 16 and 17 on "low memory" issues.
3. MINIX INSTALLATION BACKGROUND
The objective of the installation is to create a partition on your disk
and to put MINIX into it. MINIX really requires three partitions how‐
ever, so the single "primary" partition is split into three subparti‐
tions. The s0 subpartition will contain the root file system, the s1
subpartition will contain the /home file system, and the s2 subparti‐
tion will contain the /usr file system. What Windows calls "drives",
i.e C:, D:, E:, MINIX calls "file systems". MINIX does not use drive
letters, but requires that one file system is made a part of another
file system by "mounting" one on the other. The "root" file system is
always present and starts with the directory "/", the root of the
directory tree. The root file system contains a few programs in /bin,
device files in /dev, and configuration files in /etc. This is just
enough to get the system started. MINIX will soon extend its directory
tree by mounting a file system on the /usr directory. What is hence‐
forth known as the /usr file system contains all MINIX programs in
/usr/bin, file system sources in /usr/src, etc, etc. The ROOT.MNX
image contains the complete MINIX root file system, but USR contains
just a small subset of the /usr file system, with just enough utilities
to install MINIX. The complete /usr file system is split up into the
USR.TAZ, SYS.TAZ and CMD.TAZ archives that are installed later to fill
/usr.
Let's suppose your first hard disk, which has device name /dev/c0d0,
has Windows already present in the first primary partition
(/dev/c0d0p0), and some free space left after that. After MINIX is
installed in that free space the disk will look like this:
/dev/c0d0 Whole hard disk #0
/dev/c0d0p0 Windows C: drive
/dev/c0d0p1 MINIX primary partition
/dev/c0d0p1s0 MINIX root partition
/dev/c0d0p1s1 MINIX /home partition
/dev/c0d0p1s2 MINIX /usr partition
/dev/c0d0 is the sum of a partition table, /dev/c0d0p0 and /dev/c0d0p1.
Likewise is /dev/c0d0p1 the sum of a subpartition table, /dev/c0d0p1s0,
/dev/c0d0p1s1, and /dev/c0d0p1s2. Read the "DEVICES" sections for more
information on MINIX devices.
4. INSTALLATION
You can install MINIX automatically or manually as described in the
sections below. The end result is the same, but manual installation
allows one to deviate from the preconfigured choices. You may wish to
read the manual pages of the programs used below before you start. You
may especially want to read boot(8) if your machine is different from
what the majority buys, because you may need to set a few boot parame‐
ters to configure drivers. To do this type ESC to get to the Boot Mon‐
itor prompt, set the appropriate variables, use save to store the set‐
tings and menu to continue where you left off.
To install the system you need two diskettes: a bootable root diskette
and a diskette full of binaries to use as /usr. These diskettes are
named ROOT and USR. These two diskettes may also be combined on a sin‐
gle high density diskette. In that case the USR part is on the p2 par‐
tition.
Insert the ROOT diskette, boot the machine and type '=' to the menu.
The MINIX kernel is loaded and takes control when you see the copyright
banner. After loading the root diskette into the RAM disk you will be
asked to finish the name of the device to mount on /usr. Type fd0p2
for a diskette that contains both ROOT and USR, otherwise replace ROOT
by USR and type fd0. Login as root.
5. AUTOMATIC INSTALLATION
Before starting the installation, you must either have a free partition
available or have at least 35 MB not in any partition so you can create
a MINIX partition.
Type setup to start the installation script. First it offers to
install a national keyboard map. The names should be clear, except for
us-swap, which swaps the CTRL and CAPS LOCK keys of a standard US style
keyboard for people who believe that the natural place of CTRL is next
to A. The default suggested between [ and ] is the US standard key‐
board.
The next thing to do is to make a partition, for this you are placed in
a partition table editor named part. This partition table editor is
very easy to use (in the author's opinion), but you will probably hate
it. You can move all over the place with the arrow keys, change val‐
ues, and make a mess of your partition table real quick. So if you get
into trouble, type 'q' to quit, 'n' to not write the table, and RETURN
to start over. Use the '?' key to get help.
With the '+' and '-' keys you can select the disk device to install on,
probably /dev/c0d0, the first hard disk. Type 'r' to load the parti‐
tion table of the selected disk. Either create one new partition by
modifying a partition marked "None", or reuse an existing partition by
changing its type to "MINIX" (hex code 81). DO NOT use part to shrink
an existing partition! It will destroy all data in that partition.
MINIX needs a partition of at least 20 MB, but not larger than 128 MB
(MINIX-86) or 1 GB (MINIX-386). The system needs 35 MB in compiled
state.
The script then wants to know the name of the partition you've created.
The partition name is probably still visible on the screen. Combined
with the drive name you have to type c0d0p1, c0d2p0 or something.
The next question is the size of the /home partition that you want.
There will be a suggested value based on the amount of disk space
available.
The new partition table is reloaded into the disk driver, and the new
MINIX partition is carved up into two or three subpartitions, a root,
the chosen amount for /home, and the rest for /usr.
After making /usr, it is immediately put to use to replace the instal‐
lation /usr file system so that you can remove the USR diskette and
insert the ROOT diskette (unless they are one and the same). The root
file system is filled with the contents of the ROOT diskette and
slightly patched up to work on the hard disk (/etc/fstab.)
You can now skip the next section and move to "TESTING", but it may be
instructive to read it anyway.
6. MANUAL INSTALLATION
The instructions that follow are at a very low level and require you to
be very careful. The big advantage is that you know precisely what
tools have been used and how everything works. The disadvantage is
that you may easily make a mistake that either forces you to start over
if you are lucky, or wipes out the contents of your hard disk if you
are not. Only if you really want to do something different should you
use a manual installation. Slavishly following the steps shown below
will only make you end up with the same result as an automatic instal‐
lation.
Run part to make partitions to load the system into. The best thing to
do is to make one large primary partition of type "MINIX" and to carve
this partition up into three subpartitions for root, /home, and /usr.
The assumption is that you will use the second partition on the first
hard disk, /dev/c0d0p1, and that c0d0p1s0 is the root subpartition,
c0d0p1s1 is /home, and c0d0p1s2 is /usr. If you want to use the first
partition on the second hard disk for instance, then substitute c0d1p0
and c0d1p0s[012] for the above. See the section on devices below, and
the manual pages of part(8) and controller(4). Start part and select
the disk that you want to install MINIX onto. In our example it will
be /dev/c0d0.
Use part to make a single partition in the primary partition table of
type "MINIX", then hit '>' on this new partition to make a subpartition
table.
For the root subpartition you are advised to use 1440 kb exactly. You
can make it larger if you want to, but it is advisable never to let the
contents outgrow a floppy. (The ROOT diskette is a copy of a root file
system, and will be used to fill your root subpartition.)
The second subpartition is for the /home subpartition. You may choose
to store your personal files there.
Use the rest of the partition for s2, the /usr subpartition.
When you are done check that /dev/c0d0p1s0 is active (the * after the
partition number) so you can boot from it later.
After making the partitions you do not have to reboot. The disk driver
reloads the partition tables on the next access if the disk is not in
use. (Open or mounted.)
To be able to boot from /dev/c0d0p1s0 you must place a master bootstrap
in /dev/c0d0p1. It has been placed there by part if it told you that
it was creating a new partition table, but
installboot -m /dev/c0d0p1 /usr/mdec/masterboot
will put it there for sure.
Next make a file system for on-disk /home. Leave it empty for now.
mkfs /dev/c0d0p1s1
Next make a file system for on-disk /usr and copy the floppy /usr on to
it.
mkfs /dev/c0d0p1s2
mount /dev/c0d0p1s2 /mnt
cpdir -v /usr /mnt
This will create a file system on /dev/c0d0p1s2, mount it on /mnt, and
copy the contents of the USR floppy onto it.
You can now use the new /usr in place of the USR floppy:
umount /dev/c0d0p1s2
umount /dev/fd0 # fd0p2 if combined
mount /dev/c0d0p1s2 /usr
This little dance has freed up your floppy drive, so please remove the
USR diskette and replace it by the ROOT diskette. Make a file system
for the root with at least 512 inodes (files), and fill it from the
floppy:
mkfs -i 512 /dev/c0d0p1s0
mount /dev/fd0 /fd0
mount /dev/c0d0p1s0 /mnt
cpdir -v /fd0 /mnt
umount /dev/fd0
Remove /mnt/etc/issue to get rid of the "use setup" message that greets
you when you boot, and edit the file /mnt/etc/fstab to name the devices
MINIX has been installed on. In our example it should look like this:
root=/dev/c0d0p1s0
home=/dev/c0d0p1s1
usr=/dev/c0d0p1s2
Unmount the new root:
umount /dev/c0d0p1s0
Make it bootable:
installboot -d /dev/c0d0p1s0 /usr/mdec/bootblock boot
The automatic script would now set the rootdev and ramimagedev boot
variables. You can do this now using the edparams command, but it is
easier to postpone it until the testing phase. The settings should be:
rootdev=c0d0p1s0
ramimagedev=c0d0p1s0
7. TESTING
By now a new MINIX system is present on your hard disk. Time to see if
it works. Leave the ROOT diskette in the drive and type halt. You are
now going to use the power of the Boot Monitor on the diskette to boot
the MINIX partition on the hard disk. Use the monitor command boot
c0d0p1 to boot the primary partition MINIX has been installed in. (It
is "c0d0p1" in our example.)
The hard disk bootstrap is now showing the menu again. You can type
'=' to start MINIX, but you probably want to change the boot parame‐
ters. Hit ESC once more to get to the command prompt. The command set
shows what the current parameters are. Here is an example that shows
how to make a menu to either start MINIX or boot Windows:
minix(=,Minix) boot
win(w,Windows) boot c0d0p0
save
Windows is assumed to be in the first partition in the example above
(c0d0p0). When finished type menu to see if the menu looks right. If
so hit '=' to start MINIX. Log in as root.
8. ADDING PROGRAMS AND SOURCES TO /usr
The setup command can also be used to add files from floppy sets to the
system. The USR.TAZ (programs and stuff), SYS.TAZ (system sources),
and CMD.TAZ (commands sources) are all installed relative to the /usr
directory, so the command to use three times is
setup /usr
Setup will ask for the size of data on the floppies, which is by
default simply the entire floppy. You will see some "Cannot make
directory" errors while extracting, as some directories already exist.
Ignore these messages. You need the USR.TAZ set if you want a working
MINIX system, SYS.TAZ if you want recompile the system or study it, and
CMD.TAZ if you also want the sources of the commands. On a disk space
starved machine you could opt to do without the commands sources, as
they are not absolutely necessary to understand MINIX.
If your machine does not have enough memory to run setup /usr then type
these commands manually:
cd /usr
vol /dev/fd0 | zcat | tar xvfp -
If USR.TAZ is already present on the hard disk in an DOS or Windows
partition, then this command can be used under MINIX-386 to extract it
to avoid the floppy detour:
cd /usr
mtools copy c0d0p0:USR.TAZ - | setup /usr
In 16-bit mode you don't have mtools, but maybe dosread will work:
cd /usr
dosread c0d0p0 USR.TAZ | setup /usr
The file doesn't have to be in the root directory of c0d0p0, of course,
c0d1p0:/TMP/USR.TAZ would name a file on the first partition of the
second hard disk in the directory \TMP.
The /usr file system can also be filled through a network from a remote
host if MINIX if you can get networking going with the NET.TAZ supple‐
ment. Use setup / to install NET.TAZ (note that it goes into / instead
of /usr), then follow the instructions in boot(8) to configure TCP/IP
and boot MINIX. There are now two ways to fill /usr. One is to add
the host name and login name of a remote host and a remote user to
/.rhosts, as root, and to use the following command on the remote host:
rsh -l root minix-box setup /usr < USR.TAZ
Two is to use fetch to copy the data directly from a Web or FTP site by
using these commands under MINIX:
cd /usr
fetch -q -o - url.../USR.TAZ | setup /usr
The sources may be installed using exactly the same commands, but with
USR.TAZ replaced by SRC.TAZ. Note that this means that the sources
must also be extracted relative to /usr.
9. NAMES
A standalone machine will have to be given a name. As root type
echo name >/etc/hostname.file
to change the host name of your machine to name.
10. ACTIVE ON BOOT
You may want to make the MINIX partition active so that it is automati‐
cally booted. With Windows fdisk or MINIX part, mark the primary par‐
tition that contains MINIX active. Using the menu you made earlier you
can boot either MINIX or Windows at a keypress. You can even set time‐
outs. To boot MINIX automatically after 5 seconds:
main() {trap 5000 minix; menu}
See monitor(8) for all the details on the monitor.
If you don't trust this then you can rig up a diskette that boots the
MINIX partition when left in the drive:
installboot -m /dev/fd0 /usr/mdec/jumpboot 010
The numbers 010 indicate the device (disk or partition) that must be
booted, i.e. /dev/c0d0p1s0 in this example. Take the name of the
device, and use the disk, partition and subpartition numbers, or less.
So c0d1p2s0 -> 120, c0d3 -> 3, c0d2p0 -> 20.)
11. DEVICES
A crash course on the MINIX devices in /dev: The first two hard disks
are named c0d0 and c0d1. These devices address the entire hard disk,
from the first to the last byte. Each disk has four partitions, for
disk 0 they are c0d0p0, c0d0p1, c0d0p2, and c0d0p3. And for disk 1
they are named c0d1p0 to c0d1p3. These partitions may contain file
systems, c0d0p0 often contains the MS-DOS or Windows "C:" file system.
MINIX can use these partitions for file systems too, but you can also
partition one of these "primary partitions" into four so-called "sub‐
partitions". The subpartitions of c0d0p0 are named c0d0p0s0, c0d0p0s1,
c0d0p0s2, and c0d0p0s3. The other partitions may have four subparti‐
tions that are named in the same way. See controller(4) for an elabo‐
rate description.
You may need to add devices to /dev, because not all devices are
present to keep down the clutter. The command MAKEDEV knows how to
make devices, and DESCRIBE can tell you what an unknown device may be,
or even what all devices in /dev may be if called without arguments.
Devices are described in dev(4), with pointers to more specific pages.
12. EDITORS
The editors available are elvis (a vi clone) and the old MINIX mined
editor. Of these editors only elvis can recover your file after a sys‐
tem crash. Only mined is available at installation time. (All you
need to know about mined right now is that CTRL-X gets you out of it.)
13. BOOT MONITOR VS. MINIX
The Boot Monitor uses the BIOS to address disks, so it has no idea of
controllers, it just lumps everything together and ignores controller
numbers. So what the monitor thinks are d0, d1, and d2, may be c0d0
(IDE primary master), c0d2 (IDE secondary master), and c1d3 (SCSI disk
at target 3). One must keep this in mind when MINIX is installed on a
disk other than the very first. So if MINIX is installed in the third
partition of the SCSI disk, then boot d2p2 will boot it, and root‐
dev=c1d3p2s0 will tell MINIX where its root file system is.
14. NATIONAL KEYBOARDS
The directory /usr/lib/keymaps contains keymap tables for several
national keyboards. If you have a German keyboard for instance, then
loadkeys /usr/lib/keymaps/german.map
will load the German key translation table into the keyboard driver.
Copy the map to /etc/keymap once MINIX is installed on the hard disk,
because having to type a key sequence like one of these:
loadkezs -usr-lib-kezmaps-german.map
loqdkeys =usr=lib=key,qps=french.,qp
on a reboot gets a bit annoying after a while. Send corrections and
new keymaps to the person named below. (Do not send a Dutch keymap,
buy yourself a real keyboard instead.)
SUGGESTIONS
Below are a few useful suggestions. Some of the information can be of
use in other situations than described here.
15. VIRTUAL CONSOLES
Hold down the ALT key and press the left or right arrow key, F1, or F2.
This switches the console between two login sessions. (Unless you have
an old mono adapter, because virtual consoles sit in video memory, and
a mono adapter only has memory for one.)
Note that kernel messages, including function key output, only appear
on the first console. This may be confusing, but it keeps the other
consoles clean.
16. LOW ON MEMORY
The normal installation requires that you have enough memory for a
large RAM disk. You can still install MINIX normally if you either
have a high density diskette drive for a combined root+usr floppy, or
you have two floppy drives of at least 720 kb. Before booting you have
to set the variable rootdev to the same value as ramimagedev. This is
slower then a RAM disk, but saves a lot of memory.
The automatic installation script knows how to handle this new situa‐
tion. If you install manually then you have to use
cpdir -vx / /mnt
to copy the root device to disk. When it is time to fill /usr and you
only have one floppy drive then hit DEL to get out of the installation
script and reboot as described in "TESTING". You can then finish the
installation manually.
17. LOW ON MEMORY AND ONLY ONE 720 KB FLOPPY DRIVE
If you only have one 720 kb floppy drive and your system is low on mem‐
ory then you can use the TINYROOT.MNX boot image. This image contains
a small kernel with only the BIOS disk driver, and a small root file
system. You can use this disk to boot your machine. Use the normal
ROOT.MNX to install the root file system. Keep booting your machine
with TINYROOT until you have compiled a small kernel for your system.
Use the rootdev boot variable to select the hard disk root file system.
Do not use TINYROOT for anything other than booting, always use ROOT
when mentioned.
18. FLOPPY DRIVE 1 IS A HIGH DENSITY DRIVE
If you would like to install from floppy drive 1 then you need to copy
at least one sector from the USR image onto a diskette for drive 0.
The USR bootstrap has been rigged to boot the other drive.
19. INSTALLING ON A SECOND HARD DISK
MINIX doesn't care if it is installed on the second disk of a system
with two disks. The only problem is to get it booted. You can either
rig up a diskette to boot MINIX as shown earlier, or you can use the
same trick on the first disk. The command
installboot -m /dev/c0d0 /usr/mdec/jumpboot 1
will lock the first disk into booting the second disk. Note that this
command modifies the disk outside a MINIX partition, overwriting a bit
of code that has likely been put there by Windows fdisk. First verify
that the Boot Monitor can boot a Windows partition, because then the
MINIX master bootstrap can do it too.
20. LOTS OF MEMORY ON A 286
You will have a hard time making MINIX use up 3 MB memory. Memory you
can spare can be used for a "second level block cache" on the RAM disk.
The File System uses the second level cache to store copies of disk
blocks that are pushed out of the normal (primary) block cache. The
size of the primary cache is compiled into the FS server, but the size
of the second level cache can be set with the ramsize boot variable.
Set it to a number between 0 and 512. 512 kilobytes is enough to keep
most of the compiler cached.
21. LOTS OF MEMORY ON A 386+
Processes can be as big as you would like on a 386, but in practice 4
MB is a lot, and 8 MB is infinite. The installation script sets up a
second level cache for MINIX-386 of up to 1024 kilobytes. This is
because the default file system cache is only 80 kb. Your first point
of call is to get rid of the poorly performing second level cache by
setting ENABLE_CACHE2 to 0 and to assign the memory used by it to the
normal block cache by enlarging the appropriate NR_BUFS and NR_BUF_HASH
constants in <minix/config.h> with as much as you can spare. (1024 for
NR_BUFS is the minimum to keep cc -c cached. 2048 is then a nice value
for NR_BUF_HASH.) Disable the second level cache, compile a new ker‐
nel, reboot and set ramsize to 0.
22. LOTS OF DISK SPACE
The maximum file system size is 1 GB for MINIX-386 and 128 MB for
MINIX-86. (MINIX-86 can handle larger file systems, but fsck can't
check them.) Note that a MINIX file system can only contain 65535
inodes (files), so the average file should be 16 kb to completely fill
it. It may be better to make two smaller file systems. Besides, fsck
takes forever on a large file system.
SYSTEM ADMINISTRATION
The system has been set up with the idea that working as root is a bad
thing to do. As root you are in no way protected from doing stupid
things. So don't do development as root, but work as bin! Only in
exceptional cases do you want to become root. Being root is fun for
wannabe hackers; administrators know better.
To make life easier for bin, some programs like su(1), install(1) and
shutdown(8) treat bin and other members of the operator group as spe‐
cial and allow them the privileges of root. (One is an operator if
one's group id is zero.) Operators should share the shadow password of
root by having ##root in their password field. This way they all have
one face (password) to the outside world, forming no greater security
risk than root alone.
The home directory of bin contains one important Makefile. You can use
it to recompile all the commands and libraries of the system. Type
make to see the usage message. If you want to compile just one command
then you can simply type make to do so. To put it in its proper place
you have to type make install. Read the Makefiles in the commands and
lib subdirectories to understand how everything is put together. If
you are tight on memory then make may fail to traverse down the source
tree and also compile things. You will have to type make in each sub‐
directory. You can run make in /usr/src at the end to see if you've
missed something or not.
The shell used by MINIX is a minimal version of ash, the BSD shell. It
has been modified to offer simple line editing using the editline(3)
library.
The kernel is not compiled from the master Makefile. To make a new
kernel you have to step into the tools directory. There you can run
four different make commands:
make This makes all the different kernel parts and combines them in
the file named image.
make hdboot
First makes the image file and then copies it into the directory
/minix. If there are already two images in that directory then
the newest image will be removed to make space for this newer
image. It is assumed that the oldest image is the most stable
system image, one that always works, and that the newest image
is experimental. Check beforehand what /minix contains before
you run make hdboot. Remove the oldest image if you want
another image to become the stable image. The Boot Monitor
chooses the newest image in /minix to boot. You can use the
monitor command ls minix to view the images present, and set the
image variable to the full name of the image you want to use
instead if the newest doesn't work. The images in /minix are
named using the MINIX release and version numbers with an extra
revision number added to distinguish the images.
The first new kernel you would like to make is one configured for your
system. The kernel you are running now contains several drivers you
don't need, or may be missing drivers that you might want. In
<minix/config.h> you can find a number of ENABLE_XXX variables that can
be set to 0 to exclude, or 1 to include a particular driver. The full
list of configurable parameters and what they do are described in con‐
fig(8). It is invaluable in figuring out what to change and how in
<minix/config.h>.
Configuring a new kernel is sometimes not enough to enable new devices,
you sometimes need to use the MAKEDEV command to make new device files
in /dev. For pseudo-ttys you also have to check if /etc/ttytab men‐
tiones the new devices.
New additions to the system can be made in the /usr/local tree. An
empty directory tree has been set up for you and binaries and manual
pages are already in the search paths. You can make a new user entry
with the adduser command.
The TZ variable in /etc/profile tells the time zone offset from the
wall clock time to GMT. You have to change it for your time zone.
(See TZ(5).)
The function keys produce debug dumps, showing various interesting data
about the system. F1 lists processes and F5 shows ethernet stats,
which may be of use now. Read console(4) to know all the details of
the screen and keyboard.
23. SYSTEM SHUTDOWN
You can't just turn a MINIX system off. MINIX must be told to flush
the modified data in the file system cache first. The following com‐
mands/keystrokes can be used to exit MINIX properly:
shutdown
First alert all users and then all processes of the impending
shutdown then halt or reboot the system in one of various ways.
See shutdown(8).
reboot / halt
Alert all processes of the system shutdown then reboot or halt.
CTRL-ALT-DEL
Halt the system by running shutdown -h now.
MINIX halts by returning to the Boot Monitor, MINIX reboots by
instructing the monitor to reboot MINIX. (MINIX is just a subprocess
to the monitor.) Either halt MINIX and use monitor commands to escape
MINIX, or use shutdown -R to reset the system.
When exiting MINIX running under DOS the Boot Monitor's exit command
will return you to the DOS prompt. The Boot Monitor and MINIX are
together just a pretty big DOS program as far DOS is concerned.
FILES
/usr/ast Honorary home directory of Andrew S. Tanenbaum. Doubles as
the place where the default setup for a new user is found.
SEE ALSOdosminix(8), monitor(8), boot(8), part(8), mkfs(1), mount(8), M(8),
fstab(5), hier(7), config(8), console(4), dev(4), adduser(8), TZ(5),
shutdown(8).
"Operating Systems - Design and Implementation 2/e" by Andrew S. Tanen‐
baum and Albert S. Woodhull.
NOTES
The notation <file.h> refers to a C language include file in
/usr/include.
Root and bin do not have the current directory in their program search
path to avoid executing programs left around by malicious people. This
means that to run foo from the current directory, ./foo must be typed.
BUGS
There are many PS/2 models, all different. Some will run MINIX, some
won't, some crippled if you lie to MINIX by setting processor to 86.
Almost no PS/2 has a standard disk, so setting c0 to esdi or bios will
be necessary.
Except for the floppy driver, none of the DMA based drivers know about
DMA being limited to a 24 bits address, i.e. the first 16 MB. So under
MINIX-386 you run a slight risk that a tar or dd command may use a buf‐
fer above 16 MB for reading or writing to a character device. This
only happens if the low 16 MB is taken by some huge processes, and you
have more than 16 MB, of course.
AUTHOR
Kees J. Bot <kjb@cs.vu.nl>
USAGE(8)